Loadmidwest558

• Completely open source host drivers, no binary object files.
• Framework for supporting new chips, including mac80211-aware embedded chips.

• Does not support older PCI/PCIe chips with SSB backplane (see b43).

• brcmsmac is a mac80211-based SoftMAC driver, and brcmfmac is a FullMAC driver.

• Broadcom Inc. | Connecting Everything
• Cached
• BCM4323 USB WIFI - Catalogue PC Drivers, New Drivers, Drivers ...
• Bcm43236 Driver

Vendor: Broadcom Corp. / Device: BCM43236 802.11abgn Wireless Adapter. This package contains the binary firmware for wireless network cards supported by the brcmsmac or brcmfmac driver. Broadcom BCM43236 firmware (brcm.

Contents

1. Supported Chips
2. Broadcom brcmsmac driver
3. Broadcom brcmfmac driver
4. Developer information

brcmsmac (PCIe/AXI) driver:

Please note: at least BCM4313 is not fully supported. Some models appears to work (users reported success), but some don't, and there's no indication that this is going to change. For example: http://marc.info/?t=138817851800006&r=1&w=2

brcmsmac (SoC/AXI) driver:

brcmfmac

PCIe devices

SDIO devices

USB devices

Both brcmsmac and brcmfmac drivers require firmware files that need to be separately downloaded. Firmware is available from the Linux firmware repository at:

• git://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git

• http://git.kernel.org/?p=linux/kernel/git/firmware/linux-firmware.git

• https://git.kernel.org/?p=linux/kernel/git/firmware/linux-firmware.git

BCM43231 and BCM43236 (rev <= 2) have another architecture and can't be easily supported by brcmfmac. They have less memory on the chip and can't run full MAC firmware, so they require implementing some extra code in the Linux driver. On the other hand they are not standard soft MAC devices, so they can't be supported by brcmsmac or b43.

• Support for both 32 and 64 bit Linux kernels

Firmware installation

Copy brcm/bcm43xx-0.fw and brcm/bcm43xx_hdr-0.fw to /lib/firmware/brcm (or wherever firmware is normally installed on your system).

• Support for both 32 and 64 bit Linux kernels

Firmware installation

Current

For SDIO driver you need to copy the nvram for your system and place it in /lib/firmware/brcm. The nvram file name depends on the chip you have. The kernel log will tell you the exact file name. For the USB driver no nvram file is needed.

The firmware files are located in the linux-firmware repository and can be copied as is to /lib/firmware/brcm.

SDIO chip on older kernels (before 3.13)

In kernel priors to v3.13 the SDIO driver used generic firmware names. Below are the instruction Use the nvram file installed in your system and copy it to /lib/firmware/brcm/brcmfmac-sdio.txt The firmware can be found in the linux-firmware repository.

Alternatively, when not available the Android version can be used as well:

For driver issues and/or bug reports, please use:

Broadcom Inc. | Connecting Everything

brcm80211-dev-list@broadcom.com

For any other questions feel free to contact the developers listed below:

Arend van Spriel arend@broadcom.com

Franky Lin frankyl@broadcom.com

Hante Meuleman meuleman@broadcom.com

Cached

Brett Rudley brudley@broadcom.com

Overview

• On-chip firmware loaded using standard request_firmware()
• Infrastructure for future chips in place.
• AMPDU support
• tracepoint support

softmac driver specifics

• Integrated with mac80211
• Using BCMA bus driver
• Uses minstrel_ht rate algorithm
• HW based encryption not enabled yet
• monitor mode

fullmac driver specifics

• Integrated with cfg80211
• Most of Mac functionality is performed on chip
• support for SDIO and USB
• SoftAP
• P2P
• TDLS

Get the code

The driver is available in linux mainline and development is done on the wireless-testing tree, available at:

The driver is also available in the 3.2 and newer kernels. When using 'make menuconfig' it can be accessed:

Location: -> Device Drivers

• -> Network device support

  • -> Wireless LAN

    • -> < > Broadcom IEEE802.11n PCIe SoftMAC WLAN driver

    • -> < > Broadcom IEEE802.11n embedded FullMAC WLAN driver

      • -> [ ] SDIO bus interface support for FullMAC driver

      • -> [ ] USB bus interface support for FullMAC driver

For the PCIe SoftMAC WLAN driver (brcmsmac) you need to enable select the BCMA bus driver as well:

BCM4323 USB WIFI - Catalogue PC Drivers, New Drivers, Drivers ...

Location: -> Device Drivers

• -> Broadcom specific AMBA

  • -> <M> BCMA support

    • -> [*] Support for BCMA on PCI-host bus

tracepoint support

Bcm43236 Driver

Both brcmsmac and brcmfmac have several tracepoints defined that can be traced using kernel Ftrace. Python-based plugins are available on Github: https://github.com/arend/brcm80211-trace-cmd

To be done for softmac driver

• Add support for
  • 40MHz channels
  • powersave
  • debugfs (for accessing counters and other diagnostic info)
  • IBSS
  • AP
  • LED support
  • HW-based encryption
  • Add support for more chips, including (near term) BCM43227, BCM43228, and BCM4331. Support for additional new chips to follow.

To be done for fullmac driver

• Add support for
  • debugfs (for accessing counters and other diagnostic info)
  • monitor mode
  • Add support for more chips.

Regulatory Implementation for brcmsmac

This generation of chips contain additional regulatory support independent of the driver. The devices use a single worldwide regulatory domain, with channels 12-14 (2.4 GHz band) and channels 52-64 and 100-140 (5 GHz band) restricted to passive operation. Transmission on those channels is suppressed until appropriate other traffic is observed on those channels. Within the driver, we use the ficticious country code 'X2' to represent this worldwide regulatory domain. There is currently no interface to configure a different domain. The driver reads the SROM country code from the chip and hands it up to mac80211 as the regulatory hint, however this information is otherwise unused with the driver.